What does ec mean on a hot tub

Add pH Increaser according to Manufacturers Instructions. The Spa has just been powered up and is in Priming Mode for 4 Minutes. This is Not an Error Message. This indicates a Possible Problem with the System Board. Test and Reset the G. Press "Mode" Button to Clear Message.

Clean and Condition Wood per Manufacturers Instructions. Add Sanitizer according to Manufacturers Instructions. On a spa with a pump suction blockage switch, the vacuum switch has closed indicating that there has been a suction problem or an entrapment avoided.

Press any button to reset after the problem has been corrected, or or contact your Dealer or Service Organization.

The Sensor Connected to the "Sens. Monitoring the Sensors will Continue for 1 Hour. In this case, if the extreme conditions are determined, the spa will display the StU message until the spa is shut down It will also set the HOt flag HOt does not appear in the display.

If the spa is powered up again the HOt message will appear on the display and the spa will not be allowed to operate until a technician evaluates the spa and resets the HOt fault by powering up in Test Mode DIP Switch A1 on the System Board. It may be possible for the stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first. This turns on pump 1, and also turns on the circ pump.

If the Circ Pump is primed, or if you Do Not have a Circ Pump, then: - Repeat the action above for each numbered pump, one at a time, by pushing its corresponding Jets button. Blocked Suction Fitting. Blocked Skimmer.

Dirty Filter. Too Many Closed Jets. Closed Slice Valve. Heat Related Pump Not Running. Heat Related Pump Not Primed. Cycling the power will clear the gFI fault and run the test again. The purpose of this feature is to: Verify that the spa has been properly installed in conjunction with a GFCI. Allow the System to trip the GFCI in the event of an extreme overheat that is characterized by a stuck, or "welded" pump relay.

If Not, Continue to Next Step. Remove the jets and clean them to remove calcium and dirt deposits. As mentioned above, the most common sign that your hot tub has an air lock is the jets not working when powered on. This can include nothing coming out of your jets when they are turned on or even a humming sound coming from the jets or pump. Hi-limit sensor may be defective, or the spa is overheating. Try restarting the spa. The flow switch is located behind the outside walls of the spa and connected to the plastic piping.

Note: Economy mode should only be used if you are not planning on using the hot tub for two or more days, any less than that and it is more efficient to keep it at a set temperature.

You can instead lower the set temperature by 2 degrees. Your hot tub factory settings will be at 38 degrees, but body temperature of 37 degrees is a generally good start for your hot tub. This may be that women on the whole tend to feel the cold more than men. What is the right hot tub temperature when not in use? A rule of thumb is that the temperature should be at least 5 degrees lower than when in use.

Filtration cycles are periods of time when hot tub pumps are scheduled to run automatically, circulating water and chemicals through the filter system and pipes—regardless of whether the spa is in use or not.

A hot tub full of standing water is the perfect breeding ground for bacteria. Viking Spa Owners on the internet are very favorable towards their hot tubs, consistently placing placing them on lists of the best hot tubs brands. Users report solid, long lasting, reliable build quality, as well as reasonably priced features. Standard Mode is programmed to maintain the desired temperature.

Note that the last measured spa temperature displayed is current only when the pump has been running for at least 2 minutes. The GFCI will reset and the spa will turn back on. The spa is now safe to use. Airlocks occur when air becomes trapped in the hot water or central heating system. Low water level, a clogged pump impeller, closed valves, clogged pipes or blocked spa drain covers can also cause flow issues.

How often should you change hot tub water? We recommend you completely change the water in your hot tub at least once every three months. That's a very general guideline, though. You can get more specific with a little data and yes, some math.

How do you flush out a hot tub? Flush the Plumbing System from the pipes, turn the jets on high, and allow the water to circulate for 15 to 30 minutes. This system flush will break up much of the sludge and grime that has built up inside the pipes of your hot tub and allow it to become trapped in the filter. What does SL mean on a Viking Spa?

Preset filter cycles The first filter cycle begins 6 minutes after the spa is energized. How do I drain my hot tub for the winter? Let the Chemicals Dissipate.

Before you drain all the water into your yard or other location, you need to allow the chemicals levels to drop. Turn Off the Breaker.

Drain the Hot Tub. Drain The Blower. Loosen the Unions on the Pumps and Heater.